.

Bitte einen Suchbegriff eingeben - Lütfen bir arama terimi girin
Kategori:
    Üretici firma:
      makineler:
        tüccar:

          Bandsaw - Horizontal

          Machinelist: Bandsaw - Horizontal


          Bandsaw - Horizontal

          used Saws Bandsaw - Horizontal MEP SHARK 512 SXI EVO


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66330 · Bandsaw - Horizontal

          MEP - SHARK 512 SXI EVO - - NEU -

          Technical details
          cutting diameter 330 mm︱capacity 90 degrees: flat 510 x 320 mm︱capacity 90 degrees: square 320 x 320 mm︱turning speed range: 40 / 80 m/min︱dimensions of saw-band 3440 x 27 x 0,9 mm︱engine output 1,5 / 1,8 kW︱weight 670 kg︱
          Semi-automatic, electro-hydraulic band saw machine for cutting 60° left to 60° right. Versatile machine with a tape of 4640 x 34 x 1.1 mm for the Cutting pipes, profiles and beams up to a maximum cutting range from 510x320 mm to 0°. The control console on a swiveling arm allows for comfortable and safe operation from any position. Electronic inverter for continuous belt speed regulation from 15 to 100 m/min. Large turntable with a diameter of 280 mm and engraved exact fine scaling, easily adjustable and stored.
            cutting diameter 330 mm
            capacity 90 degrees: flat 510 x 320 mm
            capacity 90 degrees: square 320 x 320 mm
            turning speed range: 40 / 80 m/min
            dimensions of saw-band 3440 x 27 x 0,9 mm
            engine output 1,5 / 1,8 kW
            weight 670 kg
            Description :
            Semi-automatic, electro-hydraulic band saw machine for cutting
            60° left to 60° right.
            Versatile machine with a tape of 4640 x 34 x 1.1 mm for the
            Cutting pipes, profiles and beams up to a maximum cutting range
            from 510x320 mm to 0°.
            The control console on a swiveling arm allows for comfortable and
            safe operation from any position.
            Electronic inverter for continuous belt speed regulation
            from 15 to 100 m/min.
            Large turntable with a diameter of 280 mm and engraved
            exact fine scaling, easily adjustable and stored.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal MEP SHARK 332-1 SXI EVO


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66328 · Bandsaw - Horizontal

          MEP - SHARK 332-1 SXI EVO - - NEU -

          Technical details
          cutting diameter 300 mm︱capacity 90 degrees: flat 330 x 260 mm︱capacity 90 degrees: square 260 x 260 mm︱capacity 45 degrees: flat 270 x 200 mm︱capacity 45 degrees: round 260 mm︱capacity 45 degrees: square 250 x 250 mm︱capacity 60 degrees: flat 170 x 170 mm︱capacity 60 degrees: square 170 x 170 mm︱capacity 60 degrees: round 180 mm︱turning speed range: 40 / 80 m/min︱dimensions of saw-band 3320 x 27 x 0,9 mm︱engine output 1,5 / 1,8 kW︱weight 670 kg︱
          Electro-hydraulic semi-automatic band saw SHARK 332 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Some features: New centralized switch console on an articulated arm. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Turntable (on roller bearings of 420 mm with preloaded thrust bearings assembled). Double belt speed (40/80 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base designed to completely contain the coolant, even with maximum angle cuts. The coolant pan (provided with an electric pump for lubrication and Cooling of the saw band) and the chip drawer (can be replaced by a Chip conveyor to be replaced - see special accessories) are in the base frame built-in. Preparation for installing the minimum blade lubrication kit (Optional, in addition to the conventional standard lubrication with emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Adjustable length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.
            cutting diameter 300 mm
            capacity 90 degrees: flat 330 x 260 mm
            capacity 90 degrees: square 260 x 260 mm
            capacity 45 degrees: flat 270 x 200 mm
            capacity 45 degrees: round 260 mm
            capacity 45 degrees: square 250 x 250 mm
            capacity 60 degrees: flat 170 x 170 mm
            capacity 60 degrees: square 170 x 170 mm
            capacity 60 degrees: round 180 mm
            turning speed range: 40 / 80 m/min
            dimensions of saw-band 3320 x 27 x 0,9 mm
            engine output 1,5 / 1,8 kW
            weight 670 kg
            Description :
            Electro-hydraulic semi-automatic band saw SHARK 332 SXI EVO with
            semi-automatic-dynamic, manual function, has a MEP-28 control
            for miter cuts from 45° right to 60° left.
            Some features:
            New centralized switch console on an articulated arm.
            Low voltage control panel:
            Polyester membrane keyboard with thermoformed highlighted
            Push buttons and actuation control signal.
            Display to show:
            * Diagnostics (messages in the user language)
            * Alarms (description of alarm causes)
            * State of inputs and outputs
            * Counting cuts
            * Time taken for the cut made
            * Current consumption of the saw blade motor
            * Saw blade tension
            * Blade speed
            * Numerical display of head position.
            Switch handle IP55 of manual 24V cycle.
            Complete program of all special cutting cycles.
            Identification of other possible special cutting cycles for special ones
            Applications
            New, latest generation hydraulic control unit, extremely powerful
            and with low energy consumption.
            Turntable (on roller bearings of 420 mm with preloaded thrust bearings
            assembled).
            Double belt speed (40/80 m/min.) with control
            Intended to accommodate an electronic inverter for the
            Continuous regulation of the belt speed from 20 to 90 m/min.
            Stroke of the saw bow can be programmed directly from the control panel
            Adaptation to the cutting material.
            Clamping device can be moved laterally to the left and right
            Quick release vice.
            Manually operated strap tension control with display on the screen
            electronic converter.
            Base designed to completely contain the coolant,
            even with maximum angle cuts.
            The coolant pan (provided with an electric pump for lubrication and
            Cooling of the saw band) and the chip drawer (can be replaced by a
            Chip conveyor to be replaced - see special accessories) are in the base
            frame
            built-in.
            Preparation for installing the minimum blade lubrication kit
            (Optional, in addition to the conventional standard lubrication with
            emulsion oil.
            Chip clearing brush.
            The machine is intended for pallet truck transport.
            Adjustable length stop for cuts of the same length
            Material support arm with roller for attaching the loading platform
            Bimetal saw band for solid and profile material.
            Tools and instructions for use in the respective user language.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal MEP SHARK 382-1 SXI EVO


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66329 · Bandsaw - Horizontal

          MEP - SHARK 382-1 SXI EVO - - NEU -

          Technical details
          cutting diameter 280 mm︱capacity 90 degrees: flat 380 x 260 mm︱capacity 90 degrees: square 260 x 260 mm︱turning speed range: 40 / 80 m/min︱dimensions of saw-band 3440 x 27 x 0,9 mm︱engine output 1,5 / 1,8 kW︱weight 670 kg︱
          Electro-hydraulic, semi-automatic band saw with additional manual and semi-automatic-dynamic function, for cuts from 45° right to 60° left. Some features: Pivoting control panel on vertical post. 420 mm large rotary table on roller bearings with preloaded thrust bearing and replaceable steel inserts. Double belt speed (40/80 m/min.)
            cutting diameter 280 mm
            capacity 90 degrees: flat 380 x 260 mm
            capacity 90 degrees: square 260 x 260 mm
            turning speed range: 40 / 80 m/min
            dimensions of saw-band 3440 x 27 x 0,9 mm
            engine output 1,5 / 1,8 kW
            weight 670 kg
            Description :
            Electro-hydraulic, semi-automatic band saw with additional manual and
            semi-automatic-dynamic function, for cuts from 45° right to 60° left.
            Some features:
            Pivoting control panel on vertical post.
            420 mm large rotary table on roller bearings with preloaded thrust bearing
            and replaceable steel inserts.
            Double belt speed (40/80 m/min.)


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal THOMAS Super Trade 350 SO


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-38732 · Bandsaw - Horizontal

          THOMAS - Super Trade 350 SO - - 2000 -

          Technical details
          capacity 90 degrees: round 270 mm︱capacity 90 degrees: square 260 mm︱ 350 x 240 ︱band speed 36/72 m/min︱saw band length 2925 x 27 x 0,9 mm︱total power requirement 1,9 kW︱weight of the machine ca. 0,6 kg︱Dimensions (LxWxH) 1,9 x 1,1 x 1,75 0︱
          Band saw including micro spray device
            capacity 90 degrees: round 270 mm
            capacity 90 degrees: square 260 mm
            350 x 240
            band speed 36/72 m/min
            saw band length 2925 x 27 x 0,9 mm
            total power requirement 1,9 kW
            weight of the machine ca. 0,6 kg
            Dimensions (LxWxH) 1,9 x 1,1 x 1,75 0
            Description :
            Band saw including micro spray device


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID GBS 218 Eco AutoCut


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66202 · Bandsaw - Horizontal

          BERG & SCHMID - GBS 218 Eco AutoCut - - -NEU- -

          Technical details
          cutting diameter 220 mm︱saw band length 2455 mm︱table height 850 mm︱cutting width 230 mm︱cutting speed 35 + 70 m/min︱dimensions of saw-band 2455 x 27 x 0,9 mm︱ 90 mm︱ 90 mm︱ 90 x 100 mm︱ 150 ︱Impact energy 150 ︱Air consume per blow 150 x 210220 mm︱stroke back stop 210 mm︱cross-slide 230 x 185 ︱total power requirement 1,2 kW︱weight of the machine ca. 0,24 t︱dimensions of the machine ca. 1,2 x 0,6 x 1,7 m︱
          SPECIAL PRICE!!! -Miter cuts up to 60° left -Cutting speed 35 / 70 m / min. - Vice with quick release device -Carbide saw band guide -Tape tension control -Electr. automatic cooling Auto-Cut-System = 3 step system -Automatic saw frame lowering via the hydraulic cylinder -Infinitely adjustable feed -with limit switch - rapid lowering of the saw frame from the rest position to the workpiece, then switch to normal saw feed -Manual mode Share of freight costs 85 EUR
            cutting diameter 220 mm
            saw band length 2455 mm
            table height 850 mm
            cutting width 230 mm
            cutting speed 35 + 70 m/min
            dimensions of saw-band 2455 x 27 x 0,9 mm
            90 mm
            90 mm
            90 x 100 mm
            150
            Impact energy 150
            Air consume per blow 150 x 210
            220 mm
            stroke back stop 210 mm
            cross-slide 230 x 185
            total power requirement 1,2 kW
            weight of the machine ca. 0,24 t
            dimensions of the machine ca. 1,2 x 0,6 x 1,7 m
            Description :
            SPECIAL PRICE!!!
            -Miter cuts up to 60° left
            -Cutting speed 35 / 70 m / min.
            - Vice with quick release device
            -Carbide saw band guide
            -Tape tension control
            -Electr. automatic cooling

            Auto-Cut-System = 3 step system
            -Automatic saw frame lowering via the hydraulic cylinder
            -Infinitely adjustable feed
            -with limit switch
            - rapid lowering of the saw frame from the rest position to the workpiece,
            then switch to normal saw feed
            -Manual mode

            Share of freight costs 85 EUR


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID GBS 242 DG HA-I


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66211 · Bandsaw - Horizontal

          BERG & SCHMID - GBS 242 DG HA-I - - -Neu- -

          Technical details
          capacity 90 degrees: round 250 mm︱capacity 90 degrees: square 210 mm︱ 290 x 210 mm︱saw band length 2.965 x 27 x 0,9 mm mm︱table height 940 mm︱band speed 35 / 70 m/min︱total power requirement 1,1/1,3 kW︱weight of the machine ca. 0,35 t︱dimensions of the machine ca. 1,3 x 0,8 x 1,5 m︱
          SPECIAL PRICE!!! Double miter metal band saw hydraulic semi-automatic with: - Hydraulic vice - Material height button - Cut monitoring by ammeter - Cutting pressure feed regulator - Belt speed 34 / 74 m/min - Miter cuts up to 60° left and 45° right - Patented, ball-bearing turntable for easy miter adjustment - Adjustable quick-release vise - Quick release lever - Automatic cooling Share of freight costs 120 EUR
            capacity 90 degrees: round 250 mm
            capacity 90 degrees: square 210 mm
            290 x 210 mm
            saw band length 2.965 x 27 x 0,9 mm mm
            table height 940 mm
            band speed 35 / 70 m/min
            total power requirement 1,1/1,3 kW
            weight of the machine ca. 0,35 t
            dimensions of the machine ca. 1,3 x 0,8 x 1,5 m
            Description :
            SPECIAL PRICE!!!
            Double miter metal band saw hydraulic semi-automatic with:
            - Hydraulic vice
            - Material height button
            - Cut monitoring by ammeter
            - Cutting pressure feed regulator

            - Belt speed 34 / 74 m/min
            - Miter cuts up to 60° left and 45° right
            - Patented, ball-bearing turntable for easy miter adjustment
            - Adjustable quick-release vise
            - Quick release lever
            - Automatic cooling
            Share of freight costs 120 EUR


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal MEP SHARK 282 CCS


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66324 · Bandsaw - Horizontal

          MEP - SHARK 282 CCS - - -Neu- -

          Technical details
          cutting diameter 250 mm︱saw band length 2950x27x0,9 mm︱table height mm︱band speed 36/72 m/min︱total power requirement 1,8 kW︱weight of the machine ca. 440 kg︱dimensions of the machine ca. m︱
          Basic equipment: Vice with quick adjustment and adjustable guide bars Hydraulic band tensioning device with tensioning pressure display Base frame with removable coolant tray Chip clearing brush Set precision stops for cuts of 0°, 45° and 60° left and 45° right Length stop for cuts of the same length Material support arm, at the same time connection option for roller conveyor/ loading side Turntable for double miter cuts Machine is intended for pallet truck/forklift transport Bimetal saw band M2 for solid and profile material Tools and instruction manual Electrical equipment: Switchboard marked cable connections Operational readiness indicator light Safety main switch Emergency stop button Speed switch Thermal magnetic protection Undervoltage release Control handle IP 55 protected Phase comparator Low voltage system 24 volts Electric coolant device 48 V (A micro spray device can be installed)
            cutting diameter 250 mm
            saw band length 2950x27x0,9 mm
            band speed 36/72 m/min
            total power requirement 1,8 kW
            weight of the machine ca. 440 kg
            Description :
            Basic equipment:
            Vice with quick adjustment and adjustable guide bars
            Hydraulic band tensioning device with tensioning pressure display
            Base frame with removable coolant tray
            Chip clearing brush
            Set precision stops for cuts of 0°, 45° and 60° left and 45°
            right
            Length stop for cuts of the same length
            Material support arm, at the same time connection option for roller conveyor/
            loading side
            Turntable for double miter cuts
            Machine is intended for pallet truck/forklift transport
            Bimetal saw band M2 for solid and profile material
            Tools and instruction manual
            Electrical equipment:
            Switchboard
            marked cable connections
            Operational readiness indicator light
            Safety main switch
            Emergency stop button
            Speed switch
            Thermal magnetic protection
            Undervoltage release
            Control handle IP 55 protected
            Phase comparator
            Low voltage system 24 volts
            Electric coolant device 48 V
            (A micro spray device can be installed)


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal Karmetal KMT KRAFT 220x250


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66287 · Bandsaw - Horizontal

          Karmetal - KMT KRAFT 220x250 - - -NEU- -

          Technical details
          cutting diameter 220 mm︱saw band length 2520 x 27 x 0,9 mm︱cutting speed 25 - 90 m/min︱table height 915 mm︱cutting width 150 x 240 mm︱ 90 mm︱ 90 mm︱ 150 mm︱Impact energy 150 mm︱connected load frequency 400 Volt︱total power requirement 1,2 kW︱weight of the machine ca. 0,35 t︱dimensions 1,4 x 0,8 x 1,5 m︱
          Rock solid band saw - Miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion - Coolant pump
            cutting diameter 220 mm
            saw band length 2520 x 27 x 0,9 mm
            cutting speed 25 - 90 m/min
            table height 915 mm
            cutting width 150 x 240 mm
            90 mm
            90 mm
            150 mm
            Impact energy 150 mm
            connected load frequency 400 Volt
            total power requirement 1,2 kW
            weight of the machine ca. 0,35 t
            dimensions 1,4 x 0,8 x 1,5 m
            Description :
            Rock solid band saw
            - Miter cuts up to 60°
            - AutoCut
            - Vice with quick clamping device
            - Belt tension control
            - Electric automatic cooling system
            - Material suggestion
            - Coolant pump


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal  AYEL-TECH CY 270N


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66284 · Bandsaw - Horizontal

          AYEL-TECH - CY 270N - - -NEU- -

          Technical details
          cutting diameter 225 mm︱saw band length 2455 mm︱table height 850 mm︱cutting width 245 x 150 mm︱cutting speed 45/90 m/min︱dimensions of saw-band 2480 x 27 x 0,9 mm︱ 90 mm︱ 90 mm︱ 145 mm︱Impact energy 145 mm︱connected load frequency 400 Volt︱total power requirement 1,5 kW︱weight of the machine ca. 0,2 t︱dimensions 1,43 x 0,72 x 1,7 m︱
          Miter band saw -Miter cuts up to 60° left -Vice with quick clamping device -Band tension control -Electr. Automatic cooling
            cutting diameter 225 mm
            saw band length 2455 mm
            table height 850 mm
            cutting width 245 x 150 mm
            cutting speed 45/90 m/min
            dimensions of saw-band 2480 x 27 x 0,9 mm
            90 mm
            90 mm
            145 mm
            Impact energy 145 mm
            connected load frequency 400 Volt
            total power requirement 1,5 kW
            weight of the machine ca. 0,2 t
            dimensions 1,43 x 0,72 x 1,7 m
            Description :
            Miter band saw
            -Miter cuts up to 60° left
            -Vice with quick clamping device
            -Band tension control
            -Electr. Automatic cooling




        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal Karmetal KMT Craft 250 x 310


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66282 · Bandsaw - Horizontal

          Karmetal - KMT Craft 250 x 310 - - -NEU- -

          Technical details
          cutting diameter 250 mm︱saw band length 3150 x 27 x 0,9 mm︱table height 700 mm︱cutting width 250 x 320 mm︱cutting speed 25 - 90 m/min︱dimensions of saw-band 2480 x 27 x 0,9 mm︱ 120 mm︱ 120 mm︱ 190 mm︱Impact energy 190 mm︱connected load frequency 400 Volt︱total power requirement 1,5 kW︱weight of the machine ca. 0,5 t︱dimensions 0,95 x 1,16 x 1,98 m︱
          Rock-solid band saw for solid material - Double miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion
            cutting diameter 250 mm
            saw band length 3150 x 27 x 0,9 mm
            table height 700 mm
            cutting width 250 x 320 mm
            cutting speed 25 - 90 m/min
            dimensions of saw-band 2480 x 27 x 0,9 mm
            120 mm
            120 mm
            190 mm
            Impact energy 190 mm
            connected load frequency 400 Volt
            total power requirement 1,5 kW
            weight of the machine ca. 0,5 t
            dimensions 0,95 x 1,16 x 1,98 m
            Description :
            Rock-solid band saw for solid material
            - Double miter cuts up to 60°
            - AutoCut
            - Vice with quick clamping device
            - Belt tension control
            - Electric automatic cooling system
            - Material suggestion


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID X-tech 900


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66255 · Bandsaw - Horizontal

          BERG & SCHMID - X-tech 900 - - -neu- -

          Technical details
          900 mm︱ 900 mm︱ 900x900 mm︱saw band length 9300 x 67 x 1,1 mm︱table height 790 mm︱band speed 14 - 60 m/min︱total power requirement 11 kW︱weight of the machine ca. 8,45 t︱dimensions 4,485 x 1,68 x 3,15 m︱
          The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.
            900 mm
            900 mm
            900x900 mm
            saw band length 9300 x 67 x 1,1 mm
            table height 790 mm
            band speed 14 - 60 m/min
            total power requirement 11 kW
            weight of the machine ca. 8,45 t
            dimensions 4,485 x 1,68 x 3,15 m
            Description :
            The semi-automatic, hydraulic saws from the X-tech line offer the best
            Saw technology and best performance when cutting special steels
            • The electro-welded machine frame and the steel saw frame meet requirements
            all cutting needs and eliminate vibration and noise.
            • The chip conveyor is hydraulically driven and the speed is
            adjustable
            • All movements of the machine (saw frame, vice, feed,
            Saw band guides) are carried out thanks to modern linear guides with high
            static and dynamic load performance, which also has very low sliding friction
            to guarantee.
            • Another characteristic feature is the roles for the
            Positioning of the material by a hydraulic motor
            are driven. They move at right angles to the material, and
            thus allowing optimal clamping of the material.
            • Thanks to the height control of the saw band position, the operator can place
            the band in
            place near the top edge of the material. After the cut is finished, the tape
            automatically raised back to the previous position. Alternatively you can
            also
            “Remain” can be selected in the lower position. During the
            The software compares the cutting load with the cutting cycle
            Default. This means that the sawing system can be stopped in the event of
            irregularities
            become.
            • The saw band is cleaned by two adjustable steel brushes. The drive
            takes place hydraulically.
            • The hydraulic unit including filter and pressure gauge guarantees one
            particularly quiet operation at constant pressure.
            • Finely ground carbide inserts that clamp the saw blade, complete with
            lateral, hardened and adjustable guide rollers. The adjustable one
            The tape guide automatically moves as close as possible to the material.
            • The saw band is tensioned via a hydraulic cylinder, which is carried out by
            the
            Machine software is controlled. The voltage is set according to a given
            Time automatically delimbed when the machine is idle or after
            a cycle has been carried out.
            • Automatic version with CNC control in the X-TECH 900 / 1200 models
            a feed length of 500 mm for the series for high production rates.
            • The material is carried by a table with seven rollers. These will
            driven by a hydraulic orbital motor through which the material
            can be placed precisely even under maximum load.
            • All guided movements are carried out by four recirculating ball guides with
            one
            high capacity for static and dynamic loading; strong
            reduced feed friction. Tempered and ground prismatic
            Guides.
            Price on request.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal UWM 260G


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66206 · Bandsaw - Horizontal

          UWM - 260G - - -Neu- -

          Technical details
          cutting diameter 227 mm︱saw band length 2455 mm︱table height 840 mm︱cutting width 260 mm︱turning speed range: 36 / 72 m/min︱dimensions of saw-band 2455 x 27 x 0,9 mm︱capacity 90 degrees: round 227 mm︱capacity 90 degrees: square 220 mm︱capacity 90 degrees: flat 260 x 220 mm︱capacity 45 degrees: round 150 mm︱capacity 45 degrees: square 145 mm︱capacity 45 degrees: flat 200 x 220 mm︱total power requirement 1,5 kW︱weight of the machine ca. 0,25 t︱dimensions of the machine ca. 0,8 x 1,4 x 1,5 m︱
          Miter band saw - automatic cut - Base frame - Coolant pump - Chip brush for cleaning the saw band - Vise with quick adjustment
            cutting diameter 227 mm
            saw band length 2455 mm
            table height 840 mm
            cutting width 260 mm
            turning speed range: 36 / 72 m/min
            dimensions of saw-band 2455 x 27 x 0,9 mm
            capacity 90 degrees: round 227 mm
            capacity 90 degrees: square 220 mm
            capacity 90 degrees: flat 260 x 220 mm
            capacity 45 degrees: round 150 mm
            capacity 45 degrees: square 145 mm
            capacity 45 degrees: flat 200 x 220 mm
            total power requirement 1,5 kW
            weight of the machine ca. 0,25 t
            dimensions of the machine ca. 0,8 x 1,4 x 1,5 m
            Description :
            Miter band saw
            - automatic cut
            - Base frame
            - Coolant pump
            - Chip brush for cleaning the saw band
            - Vise with quick adjustment


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal HBM CY-275 Autocut


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66205 · Bandsaw - Horizontal

          HBM - CY-275 Autocut - - -NEU- -

          Technical details
          cutting diameter 225 mm︱dimensions of saw-band 2480 x 27 x 0,9 mm︱table height 935 mm︱cutting speed 45 + 90 m/min︱ 225 mm︱ 145 mm︱ 90 mm︱ 150 x 245 mm︱ 190 x 150 mm︱capacity 60 degrees: flat 120 x 90 mm︱total power requirement 1,1 kW︱weight of the machine ca. 0,24 t︱Dimensions (LxWxH) 1380 x 580 x 930 mm︱
          - With an output of 1100 watts, the device is ideal for processing hard types of metal. - Thanks to the emergency stop and automatic switch-off, you can work safely - The low-noise electric motor ensures a quiet working atmosphere - Comfortable buttons guarantee pleasant operation of the device.
            cutting diameter 225 mm
            dimensions of saw-band 2480 x 27 x 0,9 mm
            table height 935 mm
            cutting speed 45 + 90 m/min
            225 mm
            145 mm
            90 mm
            150 x 245 mm
            190 x 150 mm
            capacity 60 degrees: flat 120 x 90 mm
            total power requirement 1,1 kW
            weight of the machine ca. 0,24 t
            Dimensions (LxWxH) 1380 x 580 x 930 mm
            Description :
            - With an output of 1100 watts, the device is ideal for processing hard types
            of metal.
            - Thanks to the emergency stop and automatic switch-off, you can work safely
            - The low-noise electric motor ensures a quiet working atmosphere
            - Comfortable buttons guarantee pleasant operation of the device.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID X-Rock 1250


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66256 · Bandsaw - Horizontal

          BERG & SCHMID - X-Rock 1250 - - -neu- -

          Technical details
          1000 mm︱ 1000 mm︱ 1200x1000 mm︱saw band length 11300 x 80 x 1,3 mm︱table height 790 mm︱band speed 14 - 60 m/min︱total power requirement 18 kW︱weight of the machine ca. 9,0 t︱dimensions 5,0 x 1,68 x 3,15 m︱
          The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.
            1000 mm
            1000 mm
            1200x1000 mm
            saw band length 11300 x 80 x 1,3 mm
            table height 790 mm
            band speed 14 - 60 m/min
            total power requirement 18 kW
            weight of the machine ca. 9,0 t
            dimensions 5,0 x 1,68 x 3,15 m
            Description :
            The semi-automatic, hydraulic saws from the X-tech line offer the best
            Saw technology and best performance when cutting special steels
            • The electro-welded machine frame and the steel saw frame meet requirements
            all cutting needs and eliminate vibration and noise.
            • The chip conveyor is hydraulically driven and the speed is
            adjustable
            • All movements of the machine (saw frame, vice, feed,
            Saw band guides) are carried out thanks to modern linear guides with high
            static and dynamic load performance, which also has very low sliding friction
            to guarantee.
            • Another characteristic feature is the roles for the
            Positioning of the material by a hydraulic motor
            are driven. They move at right angles to the material, and
            thus allowing optimal clamping of the material.
            • Thanks to the height control of the saw band position, the operator can place
            the band in
            place near the top edge of the material. After the cut is finished, the tape
            automatically raised back to the previous position. Alternatively you can
            also
            “Remain” can be selected in the lower position. During the
            The software compares the cutting load with the cutting cycle
            Default. This means that the sawing system can be stopped in the event of
            irregularities
            become.
            • The saw band is cleaned by two adjustable steel brushes. The drive
            takes place hydraulically.
            • The hydraulic unit including filter and pressure gauge guarantees one
            particularly quiet operation at constant pressure.
            • Finely ground carbide inserts that clamp the saw blade, complete with
            lateral, hardened and adjustable guide rollers. The adjustable one
            The tape guide automatically moves as close as possible to the material.
            • The saw band is tensioned via a hydraulic cylinder, which is carried out by
            the
            Machine software is controlled. The voltage is set according to a given
            Time automatically delimbed when the machine is idle or after
            a cycle has been carried out.
            • Automatic version with CNC control in the X-TECH 900 / 1200 models
            a feed length of 500 mm for the series for high production rates.
            • The material is carried by a table with seven rollers. These will
            driven by a hydraulic orbital motor through which the material
            can be placed precisely even under maximum load.
            • All guided movements are carried out by four recirculating ball guides with
            one
            high capacity for static and dynamic loading; strong
            reduced feed friction. Tempered and ground prismatic
            Guides.
            Price on request.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID GBS 240 AutoCut


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66204 · Bandsaw - Horizontal

          BERG & SCHMID - GBS 240 AutoCut - - -NEU- -

          Technical details
          cutting diameter 240 mm︱dimensions of saw-band 2730 x 27 x 0,9 mm︱table height 920 mm︱cutting speed 35 + 70 m/min︱ 240 mm︱stroke back stop 230 mm︱cross-slide 270x230210 ︱Impact energy 200 ︱Air consume per blow 200x210130 mm︱ 130 mm︱ 130x160 mm︱total power requirement 1,2 kW︱weight of the machine ca. 0,26 t︱dimensions of the machine ca. 0,9 x 1,6 x 1,74 m︱
          • miter left 60° • Quick-release vise with quick-release device a. • Quick release lever for easy handling • Frame and gear made from one piece, very quiet cut and very low vibration • Electrical monitoring of band tension and band breakage, saw band cover. • Carbide saw band guide • Large machine bed • Machine base (disassembled) with automatic cooling The AutoCut system consists of: Hydraulic cylinder, feed control, spring assembly, limit switch Automatic saw frame lowering via the hydraulic Cylinder, continuously adjustable feed, with limit switch at the end of the cut. Rapid lowering of the saw frame from the rest position to the workpiece, then toggle to normal saw feed (e.g. for scribing). Manual operation: The hydraulic cylinder works as a brake cylinder (e.g. for notching). Through the brake cylinder the saw can be positioned in any position during the return stroke.
            cutting diameter 240 mm
            dimensions of saw-band 2730 x 27 x 0,9 mm
            table height 920 mm
            cutting speed 35 + 70 m/min
            240 mm
            stroke back stop 230 mm
            cross-slide 270x230
            210
            Impact energy 200
            Air consume per blow 200x210
            130 mm
            130 mm
            130x160 mm
            total power requirement 1,2 kW
            weight of the machine ca. 0,26 t
            dimensions of the machine ca. 0,9 x 1,6 x 1,74 m
            Description :
            • miter left 60°
            • Quick-release vise with quick-release device a.
            • Quick release lever for easy handling
            • Frame and gear made from one piece, very quiet cut and very low vibration
            • Electrical monitoring of band tension and band breakage, saw band cover.
            • Carbide saw band guide
            • Large machine bed
            • Machine base (disassembled) with automatic cooling
            The AutoCut system consists of:
            Hydraulic cylinder, feed control, spring assembly, limit switch
            Automatic saw frame lowering via the hydraulic
            Cylinder, continuously adjustable feed, with limit switch
            at the end of the cut. Rapid lowering of the saw frame
            from the rest position to the workpiece, then toggle
            to normal saw feed (e.g. for scribing).
            Manual operation: The hydraulic cylinder works as a brake cylinder
            (e.g. for notching). Through the brake cylinder
            the saw can be positioned in any position during the return stroke.




        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal WMT CY-210


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66200 · Bandsaw - Horizontal

          WMT - CY-210 - - -NEU- -

          Technical details
          cutting diameter 170 mm︱dimensions of saw-band 2080 x 20 x 0,9 mm︱table height 880 mm︱cutting speed 40 + 80 m/min︱ 170 mm︱ 125 mm︱ 150 x 190 mm︱ 95 x 120 mm︱total power requirement 1,1 kW︱weight of the machine ca. 0,24 t︱Dimensions (LxWxH) 870 x 1.550 x 1.740 mm mm︱
          This metal band saw comes with a closed worm gear. It also has hydraulic pressure control and a base frame that can be rotated through 45 degrees. Other features include emergency stop, the complete cooling system, the factory base frame, automatic switch-off and the quick-release device.
            cutting diameter 170 mm
            dimensions of saw-band 2080 x 20 x 0,9 mm
            table height 880 mm
            cutting speed 40 + 80 m/min
            170 mm
            125 mm
            150 x 190 mm
            95 x 120 mm
            total power requirement 1,1 kW
            weight of the machine ca. 0,24 t
            Dimensions (LxWxH) 870 x 1.550 x 1.740 mm mm
            Description :
            This metal band saw comes with a closed worm gear. It also has hydraulic
            pressure control and a base frame that can be rotated through 45 degrees. Other
            features include emergency stop, the complete cooling system, the factory base
            frame, automatic switch-off and the quick-release device.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal HBM HBM 355


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66285 · Bandsaw - Horizontal

          HBM - HBM 355 - - -NEU- -

          Technical details
          cutting diameter 355 mm︱dimensions of saw-band 3770 x 34 x 1,1 mm︱cutting speed 20 - 80 m/min︱cutting width 490 x 280 mm︱ 290 mm︱Impact energy 250 mm︱ 230 mm︱ 180 mm︱connected load frequency 400 Volt︱total power requirement 2,2 kW︱weight of the machine ca. 0,7 t︱dimensions 1,43 x 0,72 x 1,7 m︱
          Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling
            cutting diameter 355 mm
            dimensions of saw-band 3770 x 34 x 1,1 mm
            cutting speed 20 - 80 m/min
            cutting width 490 x 280 mm
            290 mm
            Impact energy 250 mm
            230 mm
            180 mm
            connected load frequency 400 Volt
            total power requirement 2,2 kW
            weight of the machine ca. 0,7 t
            dimensions 1,43 x 0,72 x 1,7 m
            Description :
            Semi-automatic miter band saw
            - Miter cuts up to 45° left + right
            - Miter cuts up to 60° right
            - Vice with quick release device
            - Tape tension control via manometer
            - Electr. automatic cooling



        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal MEP SHARK 332-1 CCS


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66327 · Bandsaw - Horizontal

          MEP - SHARK 332-1 CCS - - -Neu- -

          Technical details
          cutting diameter 300 mm︱saw band length 3320 x 27 x 0,9 mm︱table height mm︱band speed 40/80 m/min︱total power requirement 1,5/1,8 kW︱weight of the machine ca. 670 kg︱dimensions of the machine ca. m︱
          How it works in the CCS version: After the material has been advanced and Once the vices have closed, the cutting process begins. The lowering is done by its own weight and is controlled by a spring balanced and a hydraulic brake cylinder regulates when the cut is carried out, the saw arm is moved by hand to the necessary position for the feed of the material is pushed up. Electrical panel (marked cable connection, indicator light for Ready for operation, safety main switch provided with padlock, Switch or speed switch, emergency stop, thermal magnetic protection, Low voltage system 24 volts) Electronic tape tension converter with on-screen display. Manual vice with quick lock Base frame with coolant tray and chip drawer, which has a Motorized chip conveyor (accessory) can be replaced. Electric coolant pump for cooling and lubricating the saw blade. Chip clearing brush Adjustable precision stops to make cuts of the same length. Machine is intended for pallet truck transport. Bimetal saw band for solid and profile material Tools and instructions for use
            cutting diameter 300 mm
            saw band length 3320 x 27 x 0,9 mm
            band speed 40/80 m/min
            total power requirement 1,5/1,8 kW
            weight of the machine ca. 670 kg
            Description :
            How it works in the CCS version: After the material has been advanced and
            Once the vices have closed, the cutting process begins.
            The lowering is done by its own weight and is controlled by a spring
            balanced and a hydraulic brake cylinder regulates when the cut
            is carried out, the saw arm is moved by hand to the necessary position for
            the feed of the material is pushed up.
            Electrical panel (marked cable connection, indicator light for
            Ready for operation, safety main switch provided with padlock,
            Switch or speed switch, emergency stop, thermal magnetic protection,
            Low voltage system 24 volts)
            Electronic tape tension converter with on-screen display.
            Manual vice with quick lock
            Base frame with coolant tray and chip drawer, which has a
            Motorized chip conveyor (accessory) can be replaced.
            Electric coolant pump for cooling and lubricating the saw blade.
            Chip clearing brush
            Adjustable precision stops to make cuts of the same length.
            Machine is intended for pallet truck transport.
            Bimetal saw band for solid and profile material
            Tools and instructions for use


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal AYEL-TECH CY 280 NL


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66288 · Bandsaw - Horizontal

          AYEL-TECH - CY 280 NL - - -NEU- -

          Technical details
          cutting diameter 235 mm︱dimensions of saw-band 2480 x 27 x 0,9 mm︱cutting width 280 x 190 mm︱cutting speed 45/90 m/min︱ 120 mm︱ 120 mm︱ 190 mm︱Impact energy 170 mm︱connected load frequency 400 Volt︱total power requirement 1,1 kW︱weight of the machine ca. 290 Kg︱dimensions 1,2 x 0,8 x 1,2 m︱
          Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling
            cutting diameter 235 mm
            dimensions of saw-band 2480 x 27 x 0,9 mm
            cutting width 280 x 190 mm
            cutting speed 45/90 m/min
            120 mm
            120 mm
            190 mm
            Impact energy 170 mm
            connected load frequency 400 Volt
            total power requirement 1,1 kW
            weight of the machine ca. 290 Kg
            dimensions 1,2 x 0,8 x 1,2 m
            Description :
            Double miter band saw
            -Miter cuts up to 60° left and 45° right
            -Vice with quick clamping device
            -Band tension control
            -Electr. Automatic cooling


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID GBS 242 DG HA-I


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66214 · Bandsaw - Horizontal

          BERG & SCHMID - GBS 242 DG HA-I - - -Neu- -

          Technical details
          capacity 90 degrees: round 250 mm︱capacity 90 degrees: square 210 mm︱ 290 x 210 mm︱saw band length 2.965 x 27 x 0,9 mm mm︱table height 940 mm︱band speed 25 - 90 m/min︱total power requirement 1,1/1,3 kW︱weight of the machine ca. 0,35 t︱dimensions of the machine ca. 1,3 x 0,8 x 1,5 m︱
          SPECIAL PRICE!!! Double miter metal band saw hydraulic semi-automatic with: - Hydraulic vice - Material height button - Cut monitoring by ammeter - Cutting pressure feed regulator - Belt speed 25 - 90 m/min - Miter cuts up to 60° left and 45° right - Patented, ball-bearing turntable for easy miter adjustment - Adjustable quick-release vise - Quick release lever - Automatic cooling
            capacity 90 degrees: round 250 mm
            capacity 90 degrees: square 210 mm
            290 x 210 mm
            saw band length 2.965 x 27 x 0,9 mm mm
            table height 940 mm
            band speed 25 - 90 m/min
            total power requirement 1,1/1,3 kW
            weight of the machine ca. 0,35 t
            dimensions of the machine ca. 1,3 x 0,8 x 1,5 m
            Description :
            SPECIAL PRICE!!!
            Double miter metal band saw hydraulic semi-automatic with:
            - Hydraulic vice
            - Material height button
            - Cut monitoring by ammeter
            - Cutting pressure feed regulator
            - Belt speed 25 - 90 m/min
            - Miter cuts up to 60° left and 45° right
            - Patented, ball-bearing turntable for easy miter adjustment
            - Adjustable quick-release vise
            - Quick release lever
            - Automatic cooling



        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal MEP Shark 281 CCS


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66323 · Bandsaw - Horizontal

          MEP - Shark 281 CCS - - -Neu- -

          Technical details
          cutting diameter 250 mm︱saw band length 2950 x 27 x 0,9 mm︱table height ca. 800 mm︱band speed 36/72 m/min︱total power requirement 1,5/1,8 kW︱weight of the machine ca. 0,37 t︱dimensions of the machine ca. m︱
          MEP sawing machine: Saw band bow, vice unit and base made of durable cast iron Precision grade marking on the cast iron structure Electrical system (with fully identifiable electrical wiring and Low voltage system 24 V) Switch handle IP 55 for manual cycles (if available) Rotating scraper brush for the saw band Clamping unit with vice for quick approach Accurate stops with adjustment for miter cuts at 0°, 45°, 60° left Bi-metal saw band 2950 x 27 x 0.9 mm Keys, instructions for use and instructions for ordering spare parts in the User language SHARK 281 with manual operation and SHARK 281 CCS with manual operation and cutting with automatic head feed by its own weight. CCS (Cut Control System) with (A switch for manual and automatic Cutting – B) Cutting speed regulation – C) Hydraulic brake with tank – D) End stop for stopping the belt) also optional for already produced machines available. Vice with quick adjustment Hydraulic converter for belt tension display Electric coolant pump for cooling and lubricating the saw band and manageable coolant tray above the base frame In the versions with a pneumatic vice (MA), the opening takes place and Closing the vise with a manual valve (with pedal control as option available)
            cutting diameter 250 mm
            saw band length 2950 x 27 x 0,9 mm
            table height ca. 800 mm
            band speed 36/72 m/min
            total power requirement 1,5/1,8 kW
            weight of the machine ca. 0,37 t
            Description :
            MEP sawing machine:
            Saw band bow, vice unit and base made of durable cast iron
            Precision grade marking on the cast iron structure
            Electrical system (with fully identifiable electrical wiring and
            Low voltage system 24 V)
            Switch handle IP 55 for manual cycles (if available)
            Rotating scraper brush for the saw band
            Clamping unit with vice for quick approach
            Accurate stops with adjustment for miter cuts at 0°, 45°, 60° left
            Bi-metal saw band 2950 x 27 x 0.9 mm
            Keys, instructions for use and instructions for ordering spare parts in the
            User language
            SHARK 281 with manual operation and SHARK 281 CCS with manual operation and
            cutting
            with automatic head feed by its own weight.
            CCS (Cut Control System) with (A switch for manual and automatic
            Cutting – B) Cutting speed regulation – C) Hydraulic brake
            with tank – D) End stop for stopping the belt) also optional for already
            produced machines available.
            Vice with quick adjustment
            Hydraulic converter for belt tension display
            Electric coolant pump for cooling and lubricating the saw band and
            manageable coolant tray above the base frame
            In the versions with a pneumatic vice (MA), the opening takes place and
            Closing the vise with a manual valve (with pedal control as
            option available)


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal MEP SHARK 282 SXI - Evo


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66326 · Bandsaw - Horizontal

          MEP - SHARK 282 SXI - Evo - - -NEU- -

          Technical details
          cutting diameter 250 mm︱capacity 90 degrees: flat 280 x 220 mm︱capacity 90 degrees: square 220 x 220 mm︱vice 285 mm︱turning speed range: 36/72 m/min︱dimensions of saw-band 2950x27x0,9 mm︱total power requirement 1,5 / 1,8 kW︱weight of the machine ca. 485 kg︱dimensions of the machine ca. 1700 x 1000 x 1800 mm︱
          Electro-hydraulic semi-automatic band saw SHARK 282 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Semi-automatic function: At the start of the cycle: - Vice closes and motor starts – Saw head lowers for the cut – Motor switches off – Saw head rises – Vise opens. Semi-automatic dynamic system (manual lowering of the saw band bow up to to the desired position and cycle start via the manual button.) Some features: New centralized control console on an articulated arm to allow the operator can be easily switched from any working position. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Large work surface with turntable on roller bearings, measuring 265 mm preloaded thrust bearing, mounted. Double belt speed (36/72 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base frame with pull-out coolant tray. Electric coolant pump for cooling and lubricating the saw band. Preparation for installing the minimum blade lubrication kit (Optional), in addition to the conventional standard lubrication Emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.
            cutting diameter 250 mm
            capacity 90 degrees: flat 280 x 220 mm
            capacity 90 degrees: square 220 x 220 mm
            vice 285 mm
            turning speed range: 36/72 m/min
            dimensions of saw-band 2950x27x0,9 mm
            total power requirement 1,5 / 1,8 kW
            weight of the machine ca. 485 kg
            dimensions of the machine ca. 1700 x 1000 x 1800 mm
            Description :
            Electro-hydraulic semi-automatic band saw SHARK 282 SXI EVO
            with semi-automatic-dynamic, manual function, has a MEP-28 control
            for miter cuts from 45° right to 60° left.
            Semi-automatic function:
            At the start of the cycle: - Vice closes and motor starts
            – Saw head lowers for the cut – Motor switches off – Saw head rises –
            Vise opens.
            Semi-automatic dynamic system (manual lowering of the saw band bow up to
            to the desired position and cycle start via the manual button.)
            Some features:
            New centralized control console on an articulated arm to allow the operator
            can be easily switched from any working position.
            Low voltage control panel:
            Polyester membrane keyboard with thermoformed highlighted
            Push buttons and actuation control signal.
            Display to show:
            * Diagnostics (messages in the user language)
            * Alarms (description of alarm causes)
            * State of inputs and outputs
            * Counting cuts
            * Time taken for the cut made
            * Current consumption of the saw blade motor
            * Saw blade tension
            * Blade speed
            * Numerical display of head position.
            Switch handle IP55 of manual 24V cycle.
            Complete program of all special cutting cycles.
            Identification of other possible special cutting cycles for special ones
            Applications
            New, latest generation hydraulic control unit, extremely powerful
            and with low energy consumption.
            Large work surface with turntable on roller bearings, measuring 265 mm
            preloaded thrust bearing, mounted.
            Double belt speed (36/72 m/min.) with control
            Intended to accommodate an electronic inverter for the
            Continuous regulation of the belt speed from 20 to 90 m/min.
            Stroke of the saw bow can be programmed directly from the control panel
            Adaptation to the cutting material.
            Clamping device can be moved laterally to the left and right
            Quick release vice.
            Manually operated strap tension control with display on the screen
            electronic converter.
            Base frame with pull-out coolant tray.
            Electric coolant pump for cooling and lubricating the saw band.
            Preparation for installing the minimum blade lubrication kit
            (Optional), in addition to the conventional standard lubrication
            Emulsion oil.
            Chip clearing brush.
            The machine is intended for pallet truck transport.
            Length stop for cuts of the same length
            Material support arm with roller for attaching the loading platform
            Bimetal saw band for solid and profile material.
            Tools and instructions for use in the respective user language.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal ZIMMER Z 252 / DG


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66210 · Bandsaw - Horizontal

          ZIMMER - Z 252 / DG - - -Neu- -

          Technical details
          capacity 90 degrees: round 250 mm︱capacity 90 degrees: square 210 mm︱ 290 x 210 mm︱saw band length 2.965 x 27 x 0,9 mm mm︱table height 940 mm︱band speed 35 / 70 m/min︱total power requirement kW︱weight of the machine ca. 0,35 t︱
          The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, - eccentric clamp, - base, - saw blade, - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.
            capacity 90 degrees: round 250 mm
            capacity 90 degrees: square 210 mm
            290 x 210 mm
            saw band length 2.965 x 27 x 0,9 mm mm
            table height 940 mm
            band speed 35 / 70 m/min
            weight of the machine ca. 0,35 t
            Description :
            The Z252/DG has the following equipment:
            - hydraulic cylinder,
            - emulsion pump,
            - eccentric clamp,
            - base,
            - saw blade,
            - 400V plug -16A-
            The machine is delivered fully assembled and ready for immediate use.


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          used Saws Bandsaw - Horizontal BERG & SCHMID GBS 242 DG AutoCut


          • WMT GmbH & Co.KG
          • Siemensstraße 1
          • 46342 Velen-Ramsdorf
          • Deutschland

          • +49 2863 92477-47
            +49 2863 92477-50
          • info@w-m-t.de
            www.w-m-t.de
          #1108-66212 · Bandsaw - Horizontal

          BERG & SCHMID - GBS 242 DG AutoCut - - -Neu- -

          Technical details
          capacity 90 degrees: round 250 mm︱capacity 90 degrees: square 210 mm︱ 290 x 210 mm︱saw band length 2.965 x 27 x 0,9 mm mm︱table height 940 mm︱band speed 35 + 70 m/min︱total power requirement 1,1 / 1,3 kW︱weight of the machine ca. 0,35 t︱dimensions of the machine ca. 1,3 x 0,8 x 1,5 m︱
          ATTENTION SPECIAL PRICE!!! Double miter metal band saw with: - Belt speed 35 + 70 m/min - Miter cuts up to 60° left and 45° right - Ball-bearing rotary table for quick miter adjustment - Quick-action clamping stick can be moved - Quick release lever - Automatic cooling
            capacity 90 degrees: round 250 mm
            capacity 90 degrees: square 210 mm
            290 x 210 mm
            saw band length 2.965 x 27 x 0,9 mm mm
            table height 940 mm
            band speed 35 + 70 m/min
            total power requirement 1,1 / 1,3 kW
            weight of the machine ca. 0,35 t
            dimensions of the machine ca. 1,3 x 0,8 x 1,5 m
            Description :
            ATTENTION SPECIAL PRICE!!!
            Double miter metal band saw with:
            - Belt speed 35 + 70 m/min
            - Miter cuts up to 60° left and 45° right
            - Ball-bearing rotary table for quick miter adjustment
            - Quick-action clamping stick can be moved
            - Quick release lever
            - Automatic cooling


        • WMT GmbH & Co.KG
        • Siemensstraße 1
        • 46342 Velen-Ramsdorf
        • Deutschland

        • Datasheet
          Request / Contact
          •   
          •   
          • 1  
          • 2  
          •   
          •   


          A horizontal bandsaw is the right tool for you
          Experience versatility and reliability with a horizontal bandsaw

          Bandsaws are extremely versatile machines in the world of metalworking. They can be used to cut a wide variety of materials at varying speeds. They come in several different sizes meaning you can find the perfect one for home or business use based on your needs. A horizontal bandsaw is a great investment as it can be used for a variety of project sizes from metalworking to woodworking. Find your next horizontal bandsaw at LagerMaschinen.

          Find used metalworking machines at LagerMaschinen

          Bandsaws offer operators a variety of advantages over other cutting methods. The uniform distribution of teeth on the cutting blade makes a horizontal bandsaw particularly useful for cutting curved and irregular shapes in metal or wood. Bandsaws offer a high level of consistency in their cuts. If you're looking to invest in a horizontal bandsaw or any other industrial equipment why not check out the variety of used equipment available at LagerMaschinen your source for the best in used machinery.

          Investing in used machinery is a smart move for any business

          When buying equipment for your home or business budgetary concerns always play a role. Optimizing both your time and money is a smart plan and can be easily done by shopping online for used equipment. Buying used machines doesn't mean sacrificing quality for affordability. If you're looking for a horizontal bandsaw or any other cutting machines you can search for products by price or location using LagerMaschinen's user-friendly platform. Save yourself time money and hassle using LagerMaschinen for your next purchase.


          Find your next automatic horizontal band saw here!
          An automatic horizontal band saw for all your needs

          Band saws are classic cutting tools that can be used on a number of different materials. Their versatility makes them perennial favorites among both hobbyists and industry specialists alike. An automatic horizontal band saw can be used both in a home workshop or in a larger factory setting. It is capable of cutting metals as well as timber. When the cutting process is complete the saw blade is automatically stopped ensuring the safety of the operator.

          Bandsaws are functional and practical for home or business

          Band saws are typically categorized into vertical and horizontal machines. Vertical band saws have a stationary blade while an automatic horizontal band saw has a mobile blade that moves through a stationary cutting surface. You can find an automatic horizontal band saw in a variety of sizes making it one of the more versatile cutting tools available. It is useful for cutting a wide variety of materials too. If you're in the market for a band saw check the selection of used machinery available at LagerMaschinen.

          Buying used machinery online is a smart investment

          Nowadays both time and money are things that scarcely anyone can afford to waste. LagerMaschinen looks to help you make the most of both by making the process of shopping for used machinery online as quick and easy as possible. For example you can search for a used automatic horizontal band saw and filter your results by price model or location to find the best machine to suit your needs. Visit LagerMaschinen to see all the advantages of online shopping!