coil line

material width 300 mm︱coil weight 3 t︱material thickness 2 - 4 mm︱

---

CNC roll feed, Make GSW, Type WVE 400/160 - weight 50/80 kg Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW

material width 200 mm︱coil weight 1,5 t︱material thickness 0,8 - 4,2 mm︱straightening roll diameter 80 mm︱Number of straightening rolls 7 Pcs.︱

---

Coil turner 2370 B Load capacity 1.5 ton. Bandwidth 300 mm Coil inner diameter: 400 - 500 mm Arm length per arm: 670 mm Dimensions: depth 1,230 mm, housing height 1,100 mm, width 1,700 mm Weight: 760 kg. Straightener Dreher 1676 AV-RA2 Material width: 200 mm Material thickness: 08 - 4.2 mm Number of straightening rollers: 7 Number of pull rollers: 4 Straightening rollers diameter: 80 mm Would be down by a running press Documents circuit diagrams, operating instructions etc. available

material width 500 mm︱coil weight 3,0 t︱material thickness 0,2 - 2,5 mm︱coil internal diameter 470 - 530 mm︱coil external diameter 1400 mm︱no. of straightening rolls 9 ︱straightening roll diameter 40 mm︱number of inlet and outlet rolls 4 ︱material cross-cut 1200 mm²︱speed 1,5 - 30 m/min︱Power capacity kW︱dimensions decoiler (WxDxH) 1,9 x 0,6 x 1,7 m︱weight decoiler 1,1 t︱dimensions straightener (WxDxH) 3,3 x 1,3 x 2,7 m︱weight straightener 3,0 t︱

---

Straightening machine RYD 40 x 500 hydraulic inlet guide Decoiler DY 500 x 3000 with hydraulic expansion, hydraulic coil lifting device elektronic roll feed AESL 500-2,8 can be offered without or with putting into operation in given condition

material width 350 mm︱coil weight 2x 1 t︱material thickness 3 mm︱coil internal dia. 480-530 mm︱coil outside dia. 1400 mm︱

---

material width 1200 mm︱coil weight 10 t︱material thickness 8 mm︱internal diameter 500 mm︱coil outside dia. 1300 mm︱coil Schleicher ︱straightening device Schleicher ︱feed motor Schleicher ︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱

---

material width mm︱coil weight t︱material thickness mm︱----------------------------------- ︱ - clamping surface (left-right) 4000 mm︱ - clamping surface (front-back) 2050 mm︱ - rotation 360 °︱ - - rotation speed 1.3 /min︱ELECTRICAL SPECIFICATIONS . ︱ - mains voltage 380 V︱ - mains frequency 50 Hz︱

---

Technical description : Blank Pallet Turnover Device / Blank Handlling (needs retrofit)

table length 3000 mm︱table width 1500 mm︱burner heads 1 ︱Control CNC ︱workpiece weight 1500 kg︱total power requirement 21 kW︱weight of the machine ca. 10,4 t︱dimensions of the machine ca. 5,2 x 4,2 x 2,62 m︱

---

CUTTING CAPACITY: STRUCTURAL STEEL 25 mm STAINLESS STEEL 15 mm ALUMINUM 12mm BRASS 8mm COPPER 8mm MACHINE AXES: 4 axes [X, Y, Z, U ] CUTTING HEAD: Precitec ProCutter CAD/CAM SOFTWARE: LANTEK EXPERT CUT *4 servo motors for all axial movements *CNC CONTROL PANEL 15 5” touch screen *IPG laser sources and coolers integrated *Precitec Procutter cutting head system *AIR FILTER (compressed air filter) *CONVEYOR BELT under cutting area *Closed housing and specially coated filter protection windows *LOADING / DISCHARGING SYSTEM *PROPORTIONAL GAS AND PIPE SYSTEM

weight ca. 300 kg︱current intensivity 20 A︱connection voltage 230 Volt︱

---

Movement X 6500 mm︱Movement Y 250 mm︱Laser Power 3600 W︱Movement Z 150 mm︱X speed max. 100 m/min︱Y speed max. 60 m/min︱Z speed max. 60 m/min︱Plate thickness MS. max. 8 mm︱Max. workpiece weight 130 kg︱Plate thickness SS max. 6 mm︱Plate thickness Al. max. 5 mm︱Laser-Typ TruFlow 3600 -︱time resonator beam on 3569 Std.︱time laser stand by 24402 Std.︱

---

The machine is checked by authorized checklist through specialists. 1. Option: Machine installation and manitnence at buyers location including function guarantyand operator training: Surcharge 42.000 € plus Transport and traveling costs Standard configuration Machine - Working range in X-axis for tubes 6500 mm - Outer circle diameter 204 mm - Flexible part removal station 3 m - NitroLine - FocusLine - Laser power control - Programmable cutting gas pressure - Programm re-entry - Automatic shut-down device - Work area lighting Laser - CO2-Laser TruFlow 2000 - Laser logbook function - Chiller Laser Cutting head - Lens cutting head with 155 mm focal length - ControlLine Controller - Sinumerik 840D - Teleservice via Internet Data Transfer - RJ45 network connection, USB-Interface Safety - CE marking - Multi-beam light barriers - Compact dust extraction unit 1500 Nm³/h - safety cabin with Macrolon panels

table length 3000 mm︱table width 1500 mm︱total power requirement 51 kW︱burner heads ︱weight of the machine ca. t︱dimensions of the machine ca. m︱

---

with changing table (without automtic storage) ByVision Touchscreen and manual control unit Technische Daten / technical details: Laserleistung / laser capacity 6 kW Materialdicke Stahl / thickness of the material steel 25 mm Materialdicke Edelstahl / thickness of the stainless steel 20 Mm Materialdicke Alu / thickness of the material Aluminium 12 mm Blechgröße x,y / sheet size x,y 3000, 1500 mm Schneidbereich x,y,z, / cutting area x,y,z 3048, 1524, 80 mm Antriebsleistung / drive capacity 51 kW Gewicht ca. / weight ca. 15000 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

working area: . ︱x-travel 3048 mm︱y-travel 1524 mm︱z-travel 170 mm︱max. table load 890 kg︱laser capacity in Watt 6000 ︱cutting speed 50 m/min︱Control Bystronic ︱

---

In our opinion, the machine is in very good condition used condition. Technical details: - Maximum workpiece thickness: - Mild steel: 25 mm - Aluminum: 15mm Accesories: - Bylaser 6000 - Cooling system - Byloader 3015 loading system - Safety barriers from Sick ***Accessories, tools and clamping devices shown are only included in the scope of delivery if this is noted in the additional information.*** ***Changes and errors in the technical data and information as well Subject to prior sale!***

Working hours machine 23304 h︱Working hours beam on 10185 h︱Laser power 4400 Watt︱Length 12800 mm︱Width 6300 mm︱Machine weight 15000 kg︱

---

table length 3000 mm︱table width 1500 mm︱burner heads Rofin Sinar DC 025 CO2 ︱Control Primach 20L ︱total power requirement 2500 W kW︱weight of the machine ca. 12 t︱dimensions of the machine ca. 12 x 6 x 3 m︱

---

working area 3000x1500 mm︱ 25 mm︱ 15 mm︱ 10 mm︱max. workpiece weight 900 kg︱ 6000 W ︱

---

Operating hours: Beam On: 42607 h Laser On: 59898 h Youtube video links: https://www.youtube.com/watch?v=nnoucK_VT_U&ab_channel=BaestleinGmbH https://www.youtube.com/watch?v=uzAdIYP3kh8&ab_channel=BaestleinGmbH

x-axis 2000 mm︱y-axis 1500 mm︱z-axis 750 mm︱burner heads 1 3 D︱laser capacity in Watt 2700 ︱

---

3D laser cutting and welding system TruLaser Cell 7020 Machine no. A0421A0099 Type: L13 standard equipment - X = 2000, Z = 750mm; B = +/- 135°; C = n x 360° - Laser TruFlow 2700 - Position laser diode - Stationary, rotatable pendant control panel - Teach panel - Teach software - Magnetic clutch, head detection - Laser power control - Power Cycles - Logbook function - focus line - Nitrogen jet aeration - Network connection including installation via teleservice - Analog modem for teleservice - Lighting boom - Documentation twice Deviating from this standard equipment or in addition the machine TruLaser Cell 7020 is equipped with: With the following configuration: Frequency 50Hz Voltage 400 V0 Electrical regulation IEC Language operating instructions German Number of operating instructions 2 pc Color standard RAL9002/5010 TruFlow 2700 Laser cutting (including preparation for laser welding) Incl. 2 cutting gases (02, N2), APC distance control, p Programmable cutting gas selection, adjustment device, Analog value cutting, pressure setting, valves Additional cutting gas argon Cutting optics f = 155 mm incl. sensor Stationary table 2000x1500 mm Second cutting optics (240 mm) Work table suction system including piping Compact deduster with 2000 Nm3/h including spark pre-separator, extraction pipe connection, for 1 active extraction point Protective cabin including separate extraction Special cover of the cabin top / roof Automatic sliding door in front Control panel including multi-button, acknowledgment and emergency stop Documentation twice / German The machine is delivered without additional Programming software, post processor and operator course. Annual service by Trumpf Service with proof Operating hours / as of 02/2022 Machine hours: 40,600h Laser on: 39,200h Beam on: 6,900h Last laser power measurement = 2790 watts (Optional) On request, we can also take care of the construction and commissioning through our laser service including training of your staff and a guarantee of 12 months (price on request)

table length 4000 mm︱table width 1500 mm︱burner heads 1 ︱Control SIEMENS 840D ︱Capacity 6000 Watt︱speed 10 m/min︱total power requirement kW︱weight of the machine ca. 19 t︱dimensions of the machine ca. 9,5 x 7,3 x 3,1 m︱

---

x-travel 1562 mm︱y-travel 772 mm︱z-travel 100 mm︱laser capacity in Watt 2200 ︱positioning speed x 100 / y 100 m/min.︱working area 3000 x 1500 mm︱fuse 80 A︱Power connection 37 kVA︱weight of the machine ca. 13,5 t︱dimensions of the machine ca. 13,5 x 2,2 x 5,60 m︱

---

Co2 ByLaser 2200M Flue gas extraction with water cooling WKL 300-F Laser power: 2.2 kW (2200 W) Maximum sheet thickness (mild steel): 8 mm Maximum sheet thickness (stainless steel): 6 mm Maximum sheet thickness (acid-resistant steel): 6 mm Maximum sheet thickness (aluminum): 4 mm Maximum workpiece dimensions (L x W): 3000 x 1500 mm 2x cutting head 5" 1x cutting head 7.5" various copper nozzles

table length 3000 mm︱table width 1500 mm︱burner heads 1 ︱ 5000 W︱workpiece weight 900 kg︱max. feed 200 / simultan x+y 300 m/min︱accuracy +/- 0,10 mm︱ 25 mm︱sheet thickness for stainless steel 20 mm︱Sheet thickness aluminum 12 mm︱control Trumpf-Sinumerik 840D ︱Power connection 105 kVA︱Required air-pressure 7-10 bar︱rated capacity 33-72 kVA︱machine weight ab. 12000 kg︱dimensions of the machine ca. 11,2 x 4,6 x 2,4 m︱transport dimension 2,98 x 2,4 B X H m︱Electric 400 Volt ︱Light barrier behind ︱Light barrier in front ︱

---

Little-used high-speed laser cutting system (flatbed / CO2) made by TRUMPF, Mod.TruLaser 5030 Classic with TruFlow 5000 with pallet changer. Design: The workpiece is stationary, the cutting head moves. X-axis as a gantry drive using servo motors and Y + Z axes with linear direct drives. Commissioned in 2007, operating hours approx.: Beam ON: 8200 h, Laser ON: 28,000 h. CNC control based on SINUMERIK 840D with color monitor 12", 64 MB, USB interface, hard disk space 500MB. Standard equipment: • Laser TLF 5000 • HI-LAS high pressure cutting • Cutting head quick change device • autom. Sheet metal outer edge detection • APC height control and process control • PCS Process Control System • Position laser diode • progr. Cutting gas selection / pressure setting • progr. Performance cycles • Microweld • PMS plasma sensors • SprintLas in all sheet thicknesses • ContourLas • AutoLas Plus • Laser power control • Spray device • Laser logbook function • autom. Pallet changer • autom. Nozzle cleaning • Work area lighting • Small parts/waste conveyor • Multi-chamber suction • Compact dust extractor • TFT color screen • Automatic switch-off • Safety devices • ToPs 100 lite • RJ 45 network connection • Network connection • 3.5" floppy drive Machine was regularly serviced by Trumpf. NEW Power Tube Basic (Send tube) installed in 04/2023 for € 7000 with 12 month warranty! The license of the TruTops Classic software for programming the machine on the PC can be purchased at an additional cost. Machine dealer with own stock of 1600 m².

table length 1250 mm︱table width 1250 mm︱burner heads 1 ︱Control Fanuc ︱output 1000 Watt︱travel -z axis 100 mm︱travel x / y 1260/1260 mm︱traversing speed 30/30/42 mm/sec︱gas consuption 10 Liter/Std.︱total power requirement 22 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. 10 m︱

---

table length 3000 mm︱table width 1500 mm︱laser capacity in Watt 4.000 Watt︱x-axis 3050 mm︱z-axis 150 mm︱y-axis 1550 mm︱burner heads Precitec HPSSL︱total power requirement 22,0 kW︱weight of the machine ca. 14.200 kg︱range L-W-H 10.360 x 5.110 x 2.310 mm︱

---

neu ︱ ca. 12 Wochen ab Auftrags ︱ Türkei ︱ 342772 €︱ 6 kW︱ Wechseltisch ︱ 25 mm︱ 15 mm︱ 20 mm︱ 10 mm︱ 12 mm︱ 3.060 x 1.530 mm︱ 3060 mm︱ 1530 mm︱ 160 mm︱ 3.048 x 1.524 mm︱ 235 kg/m²︱ 120 (HD-FL 160 m/min) m/min︱ 120 (HD-FL 160 m/min) m/min︱ 170 (HD-FL 226 m/min) m/min︱

---

FIBER LASER HESSE HD-F MADE BY DURMA The shuttle table is positioned longitudinally, which results in the best possible accessibility for optional loading and unloading systems. This system can also be optionally equipped with a linear motor drive for even higher speed and accuracy. The system consists of the following components: Shuttle table system in longitudinal direction for simultaneous loading/unloading and cutting to reduce non-productive production times Encapsulated cutting room with protective glazing CNC graphics control Siemens Sinumerik 840D Laser source Brilase Cutting head Precitec Procutter F150 with automatic focus adjustment Cooling unit for cutting head and laser source CAD/CAM software LANTEK for programming including autonesting Positioning laser Sheet check system (automatic detection of sheet position and dimensions) Automatic nozzle cleaning Central lubrication Slug box Working area lighting Multi-chamber suction system Light barrier protection for the changing table Remote maintenance access Equipment according to CE guidelines OPTIONS: Extraction unit with filters € 11.000,-- Material conveyor belt for small parts and slug € 7.290.-- Further options such as laser cutting monitoring, Durma Cloud, automatic nozzle change, 3D cutting head, pipe cutting device, loading and unloading systems with or without sheet metal tower on request. Other table sizes on request.

table length . mm︱table width . mm︱burner heads . ︱ 2 ︱total power requirement . kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱

---